Deviser TC722 – All-in-One 10G Transport Tester

• Supports 3 VLAN tags (QinQ), 3 MPLS encapsulation labels, IPv6 protocol, runt and jumbo frame configuration • Supports Terminal and Transparent Transmission test models • Supports OTN, OTU-1, OTU-1e, OTU-1f, OTU-2, OTU-2e, OTU-2f test • Supports external synchronize clock input, SyncE and IEEE 1588v2 • Supports optical power measurement • Supports remote control • Supports packet filtering and capturing Product Overview The TC722 is an all-in-one Transport Layer Tester released by Deviser to support full protocol testing at rates up to 10Gbps . The TC722 provides expert analysis for next-generation high-speed Metro and Carrier Transport networks, validating performance and connectivity while cutting OPEX and CAPEX. It is an efficient testing tool for service providers to satisfy client service level agreements (SLAs) . The TC722 is ideal for any transport testing task . It is fully equipped for Ethernet performance assessment; Metro Ethernet/SONET/SDH, and Mobile Backhaul installation, activation, or maintenance; point-to-point Ethernet access deployment; online troubleshooting for real-time information flow; and more. The tester supports multiple communication protocols to meet different testing requirements, including SyncE, IEEE 1588v2, E1/T1, SDH/SONET, and OTN Application Note • Network engineering site installation and activation test • Service providers can evaluate data transmission network performance with complete end-to-end testing • PTN/IPRAN network configuring and performance testing • Local, Metro Ethernet construction, deployment and maintenance • Communication Teaching and Research   Common functions and operations: The TC722 supports independent dual-port testing, allowing each port to conduct its own measurement . Functions include Ethernet RFC 2544, Y.1564, traffic generation and monitoring, BERT, loopback, pass through mode, SDH BER, RTD, APS, insert/discard specified tributary test, OTN BER, RTD, and APS main test functions – as well as ping, traceroute, HTTP, FTP, and other auxiliary test functions . Ethernet RFC 2544 measurement: The RFC 2544 measurement function offers two modes: remote loopback and dual-sites . Use dual-sites mode to easily perform point-to-point symmetric and asymmetrical tests . The RFC 2544 application’s test frame structure supports VLAN/QinQ/MPLS labels, and the maximum test rate can be matched to the line rate. For throughput measurements, users can freely define frame lengths once testing achieves up to eight different frame lengths.   Ethernet BERT measurement: The BERT measurement allows encapsulation testing on up to 4 layers. It supports VLAN/QinQ/MPLS label frame structures, eight PRBS (or user-defined) pattern bit error rate tests, and service interruption time tests . Encapsulate any test pattern into Ethernet frames in order to verify point-to-point characteristics on an Ethernet network, and insert bit errors or FCS errors during BERT testing in real-time . The BERT function also includes reverse-pattern setting.   Ethernet Y .1564 measurement Test network service configurations and performance in accordance with ITU-T Y .1564 standards, easily verifying the network’s achievement of SLA. The TC722 supports 10 traffic channels, which can be independently configured with different IP addresses, VLAN tags, MPLS labels, frame size, bandwidth, and more . It can also detect 0-CIR \ CIR-EIR \ overshot bandwidth, frame delay, frame jitter, frame loss rate, and frame out-of-order .   Ethernet traffic generation and monitoring function With up to 10 independently configurable traffic channels, each channel can have its own MAC address, IP address, frame length, and header format. Traffic can be generated in multiple ways: constant speed, sudden mode, ladder mode, or incremental mode . The TC722 can simulate multi-service test environment for triple play test scenarios . Intelligently discover and connect to devices, then remotely trigger a loopback state or verify QoS point-to-point performance . Also included with this application is a 1588v2 protocol packet test, returning accurate readings on CRC error frames, jabber frames, runt frame signal loss alarm, optical power measurement, unicast frames, multicast frames, broadcast frames, pause frames, frame delay, frame jitter, frame loss, frames of different length range, and symbol error.   Ethernet Loopback Up to 4 layers Smart Loopback function . This mode is divided into Transparent loopback: all traffic is looped back; L2 loopback: All traffic is looped back after switching MAC address L2 Full unicast loopback: All unicast traffic is looped back after switching MAC address L3 loopback: All traffic is looped back after switching MAC addressand IP address L4 loopback: All traffic is looped back after switching MAC address, the IP address and Port.   SDH APS/OTN APS Measurement Directly test the device-switching function under various switching conditions, and conduct accurate measurements of the SDH/OTN network automatic protection switching (APS) and service disruption time . The TC722 can simulate a real device to record and monitor K1, K2 bytes in an ITU-T G .783 linear network in real time Ethernet Pass Through Function When the passthrough function is activated, the dual ports exchange data packets – those received by Port 1 are transmitted from Port 2, and vice versa – while the TC722 records send/receive and transmission rate readings . This function aids online troubleshooting of live traffic among customers, service providers, and carriers . SDH BERT Measurement Designate either PRBS or fixed-sequence patterns as the payload . This tool supports c-12, c-3, c-4 to vc-4 multiplexing cascade, as well as four different rates: STM-1, STM-4, STM-16, and STM-64 . Users can simulate real channels to complete basic error and alarm insertion, using the TC722 as the receiver to detect channel error. .   SDH APS/OTN APS Measurement The RTD test determines the network’s Round Trip Delay and QoS information. . SDH APS/OTN APS Measurement Directly test the device-switching function under various switching conditions, and conduct accurate measurements of the SDH/OTN network automatic protection switching (APS) and service disruption time . The TC722 can simulate a real device to record and monitor K1, K2 bytes in an ITU-T G .783 linear network in real time.   Ethernet Pass Through Function When the passthrough function is activated, the dual ports exchange data packets – those received by Port 1 are transmitted from Port 2, and vice versa – while the TC722 records send/receive and transmission rate readings . This function aids online troubleshooting of live traffic among customers, service providers, and carriers . SDH BERT Measurement Designate either PRBS or fixed-sequence patterns as the payload . This tool supports c-12, c-3, c-4 to vc-4 multiplexing cascade, as well as four different rates: STM-1, STM-4, STM-16, and STM-64 . Users can simulate real channels to complete basic error and alarm insertion, using the TC722 as the receiver to detect channel error. SDH APS/OTN APS Measurement The RTD test determines the network’s Round Trip Delay and QoS information.   SDH APS/OTN APS Measurement Directly test the device-switching function under various switching conditions, and conduct accurate measurements of the SDH/OTN network automatic protection switching (APS) and service disruption time . The TC722 can simulate a real device to record and monitor K1, K2 bytes in an ITU-T G .783 linear network in real time. SDH Insert/Discard Tributary Measurement Inserts or discards the specified tributary. Also supports various error insertion operations: single, BER, Burst, alternating, continuous, and frame OTN BERT Measurement Measure BER and FEC performance, and analyze OTU-1, OTU-2, OTU-1E, OTU-2E, OTU-1F, OTU-2F optical signals in accordance with ITU-T G .709 . The instrument supports a variety of in-service and out-of-service tests, and can do single-error, error rate, alternating, continuous, or random error insertion. Specifications   Function                 Ethernet Measurement RFC 2544 Throughput, Delay, Packet Delay Variation, Frame Loss, Back to Back Y .1564 Service configuration testing, service performance testing, supports up to 10 different traffic BERT Support L1-L4 BERT support, insert error, frame error, PRBS, user-defined patterns Traffic generation and monitor Supports up to 10 different traffic QoS and BER testing Smart Loopback L1-L4 Pass Through mode Support Delay measurement Round Trip Delay SyncE Support BITS, Ethernet line clock, internal high-stability clock source VLAN 3 layers VLAN (QinQ) MPLS 3 layers MPLS IEEE1588v2 Support OAM IEEE802 .3 OAM IPv6 Support     SDH measurement BERT Insert errors, detect error RTD Get network round trip delay and network QoS information APS Automatic protection switching time and service interruption time test Insert/discard specified tributary test Insert the specified tributary, discard the specified tributary.   OTN measurement BERT Insert errors, detect error RTD Get network round trip delay and network QoS information APS Automatic protection switching time and service interruption time test Online help Support Recovery factory settings Support Name file in Chinese Support File format PDF, CSV Configure file Save personalized configure file, can import and export Screen shot function Support Touch-screen soft keyboard input Support Browser Support Auto shutdown / sleep Support Language English, Chinese General Display 7″ 800 × 480 dot-matrix TFT touchscreen   Interface USB2.0 × 2, USB power supply DC5V±0.05V@500mA LAN RJ-45 x 1 MicroSD × 1, up to 32GB   Storage Internal 8GB Flash memory External support U disk storage Battery 7.4V 5300mAh Battery, 39.22Wh Maximum 4 hours operating time Supported Rates 10Base-T, 100Base-Tx, 1000Base-T, 1000Base-SX, 1000Base-LX, 1000Base-ZX, 10GBase-SR/SW, 10GBase-LR/LW, 10GBase-ER/EW Supported Standards IEEE802 .3, RFC 2544, RFC 3393, Y .1564, G.707, G.709, IEEE1588v2 Supported Clock References Internal high stability clock source, Ethernet line recovery clock, external clock (2 .048Mbps, 1 .544Mbps, 2 .048MHz) Total Power Consumption <12W   Power Supply AC parameters 100-240V 600mA 50~60Hz DC parameters 12V 5A maximum Total power 60W maximum Mechanical and Environmental Dimensions (length × width × height) 206 mm x 171 mm x 75mm, (8 .11” x 6 .73” x 2 .95”) Weight 1 .5kg (3 .3 lbs) Operating Temperature Range -10˚C~ 50˚C Storage Temperature range -20˚C~ 70˚C Relative Humidity 0%-95% Non-condensing Battery Life Over 3 hours Battery Charge Time 5 hours for full charge